Humidity & Temperature Sensor

Product Details:

This is a low-cost digital Temperature and Humidity Sensor Module. It uses a thermistor sensor and a capacitive humidity to measure the surrounding air temperature. The output showing in digital signal on the data pin (no analog input pins needed). It's fairly simple to use but requires proper timing to grab data.

Additional Information:

• Item Code: OMP-S022
• Port of Dispatch: Mumbai

Product Details:

PRODUCT DETAILS

AM2302 output calibrated digital signal. It applys exclusive digital-signal-collecting-technique and humidity sensing technology, assuring its reliability and stability. Its sensing elements is connected with 8-bit single-chip computer.
Small size & low consumption & long transmission distance(100m) enable AM2302 to be suited in all kinds of harsh application occasions.

OTHER DETAILS

3 to 5V power and I/O

2.5mA max current use during conversion (while requesting data)

Good for 0-100% humidity readings with 2-5% accuracy

Good for -40 to 80°C temperature readings ±0.5°C accuracy

No more than 0.5 Hz sampling rate (once every 2 seconds)

Body size 27mm x 59mm x 13.5mm (1.05" x 2.32" x 0.53")

3 wires 23cm long (9")

27mm wide x 58.75mm tall x 13.30mm deep

Low cost

Additional Information:

• Item Code: OMP-S034
• Delivery Time: 1 to 2 days

Features and Advantages:-
Small size and low cost
Easy integration
Wide range of factory calibrated settings:
Sensor temperature range -40 ... + 125 ° C
Object temperature range -70 ... + 380 ° C
Ta and To range from 0 to + 50 ° C with an accuracy of 0.5 ° C
(Medical) high precision calibration
Measurement resolution up to 0.02 ° C
Single and dual view versions
Compatible with SMBus digital interface
PWM continuous reading output
3V and 5V supply voltage
The supply voltage can be adjusted from 8 ... 16V
Energy saving mode of operation
A variety of packaging methods and measurement methods for different applications
Vehicle level standardor

_{Small size, low costMounted on a breakout board with two types of pins10k Pull up resistors for the I2C interface with optional solder jumpersEasy to integrateFactory calibrated in wide temperature range:-40 ... + 125 ° C for sensor temperature and-70 ... + 380 ° C for object temperature.High accuracy of 0.5 ° C over wide temperaturerange (0 ... + 50 ° C for both Ta and To) High (medical) accuracy calibrationMeasurement resolution of 0.02 ° CSingle and dual zone versionsSMBus compatible digital interfaceCustomizable PWM output for continuousreadingSimple adaptation for 8 ... 16V applicationsSleep mode for reduced power consumptionDifferent package options for applications andmeasurements versatilityAutomotive grade}

Product Details:

The DHT22 temperature and humidity sensor is a low-cost high precision humidity and temperature sensor with a single wire digital interface.The sensor is pre-calibrated and doesn’t require extra components so you can get right to measuring relative humidity and temperature.
DHT22 temperature and humidity sensor Features:3.3 – 6 V Input1-1.5 mA measuring current40-50 uA standby currentHumidity from 0 – 100 % RH-40 – 80 degrees C temperature range+- 2 % RH accuracy+- 0.5 degrees C20 m max wire length

Additional Information:

• Item Code: OMP-M061

Product Details:

PRODUCT DETAILS

DHT-11 Digital Temperature and Humidity Sensor is a basic, ultra low-cost digital temperature and humidity sensor.

It uses a capacitive humidity sensor and a thermistor to measure the surrounding air and spits out a digital signal on the data pin.

OTHER DETAILS

Operating voltage: DC 5V

Temperature measuring range: 0-60°c

Temperature measurement accuracy: ± 2°c

Humidity measuring range: 20-90% RH

Humidity accuracy: ± 5% RH

Size: 28mm x 12mm x 8mm

FEATURES

Chip: DHT11 temperature and humidity sensor

Digital signal output

Additional Information:

• Item Code: OMP-S058
• Delivery Time: 1 to 2 Days