LCD Display

Product Details:

This is a high quality 16 character by 2 line intelligent display module, with back lighting, Works with almost any microcontroller.This is a popular 16x2 LCD display. It is based on the hd44870 display controller hence it is easy to interface with most micro controllers. It works of 5v and has a green back light which can be switched on and off as desired. The contrast of the screen can also be controlled by varying the voltage at the contrast control pin (pin 3).

Features

• 16 Characters x 2 Lines
• 5x7 Dot Matrix Character Cursor
• HD44780 Equivalent LCD Controller/driver Built-In
• 4-bit or 8-bit MPU Interface.

Additional Information:

• Item Code: OMP-M013

Product Details:

This display uses a 2-wire communications method called "IIC", "I2C" "I squared C", and "TWI". All these mean the same thing. This serial protocol that supports multiple devices on the same 2-wire bus (Plus Voltage and Ground, of course)

Power supply voltage +5V

Support I2C protocol.

I2C Address It's either 0x27 or 0x3F

Received an email from a customer saying that his board works with 0x3F

Pin Definition GNDVCCSDASCL

Power supply voltage +5V

Back lit (Blue with White char color)

Size 82x35x18 mm

Contrast Adjust Potentiometer

Additional Information:

• Item Code: OMP-M028

Product Details:

Features:

1. Resolution: 128X64

2. Ultra-wide viewing angle: 160° or more (display the maximum viewing angle of one screen)

3. Ultra-low power consumption: 0.08W ordinary screen (much lower than TFT screen).

4. Wide power supply range: DC 3V-5V (no change, directly compatible with common 3.3V and 5V power supply systems)

5. Industrial grade: working temperature range -30 degrees to 70 degrees

6. Ultra-small size: (length) MM*35.4 (width) MM*33.5 (thickness) 4.3MM.

7. Support multiple working modes: 4-wire SPI,

8. Through the selection of CS signal of the chip, multiple SPI or IIC devices can work on the same bus.

9. Support 3.3V and 5V control chip I/O level (no need for any setting, directly compatible).

10. OLED screen, internal driver chip: SH1106 (same operation as SSD1306).

11. Color: white, blue

Additional Information:

• Item Code: OMP-M127
• Delivery Time: 1 to 2 Days

Product Details:

• Parameter 
• 1. High resolution: 128*64 (same resolution as 12864LCD)' But the OLED screen has a lot of pixels per unit area 
• 2. Wide viewing angle: >160° 
• 3. Low power consumption: 0.04W in normal display 
• 4. Wide power supply range: DC
• 5. 3v-5v Industrial grade: working temperature range -30 70
• 6. Size: as shown in the figure 
• 8. Brightness and contrast can be controlled by program instructions 
• 9. Internal driver chip of OLED screen: SSD1306

Additional Information:

• Item Code: OMP-M110
• Delivery Time: 1 to 2 Days

Product Details:

1. A simplified manufacturing process compared to TFT-LCD (See comparison of Picture 1 and Picture 2 below)
2. Self-emitting light, in contrast to the required backlight for TFT-LCD
3. High luminosity
4. Lightweight and thin (less than 2 mm)
5. Capable of wide viewing angles?~180??
6. Low operating voltage and power consumption
7. Quick response (~ ? second level)
8. Wide range of operating temperatures (-40c to 85c)A Comparison of OLED and TFT-LCD Display Technologies

Features
High resolution: 128 * 64
Viewing angle:> 160 °
Supports many control chip: Fully compatible with Arduino, 51 Series, MSP430 Series, STM32 / 2, CSR IC, etc.
Ultra-low power consumption: full screen lit 0.08W
Voltage: 3V ~ 5V DC
Working Temperature: -30 c ~ 70 c
Module Size: 27.3MM *27.8MM
I2C/IIC Interface, need 2 IO only.
Driver IC: SSD1306

Additional Information:

• Item Code: OMP-M092
• Delivery Time: 1 to 2 Days

Product Details:

PRODUCT DETAILS

High Class Material This OLED display board is made of high class FR4 material, which offers the practical function and great playing effect.

Low-power The OLED display only consumes lower power, which performs better than the traditional display board.
Auto Lighting The OLED display is self-luminous, and does not need backlighting, which is quite convenient to use.
Programmable This OLED board comes with the programmable function. You can program the board and make it show different information like weather, music and date.
Replaced Part Due to its practical function and stable performance, this OLED display is a good choice as replaced part.


Color White, Blue, Yellow/Blue
Material FR4
Size Approx.2.4*2.7*0.1cm/0.94*1.06*0.03inches
Voltage3.3V-5V
Working Temperature -30°-80°
Driver ICSSD1306

Additional Information:

• Item Code: OMP-M091
• Delivery Time: 1 to 2 Days

Product Details:

Feature:
The MAX7219 is an integrated serial input / output co-cathode display driver that connects a microprocessor with an 8-digit 7-segment digital LED display or a bar graph display or 64 independent LEDs. Which includes an on-chip B-type BCD encoder, multi-scan circuit, segment word drive, but also a 8 * 8 static RAM used to store each data. Only one external register is used to set the segment current for each LED.
A convenient four-wire serial interface can be connected to all common microprocessors. Each data can be addressed at the time of updating without having to rewrite all the displays. The MAX7219 also allows the user to select or not code for each data.
The entire device contains a 150μA low power shutdown mode, analog and digital brightness control, a scan limit register allows the user to display 1-8 bits of data, and a test mode for all LEDs to emit light.
Only need 3 IO port can drive a dot matrix! Dot matrix display without flicker! Support cascade!

Module
parameters:
1. A single module can drive an 8 * 8 coin lattice
2. Module operating voltage: 5V
3. Module size: Length 12.8 cm X Width 3.2 cm X Height 1.3 cm
4. With 64 fixed screw holes, aperture 3mm
5. Module with input and output interfaces, support multiple modules cascade.
6. Light Color: Blue/Green/Red

Additional Information:

• Delivery Time: 1 to 2 days

Product Details:

LED Backlight:-4 PCS White LED Backlight ,
If=60±5mA & Vf=3.0±0.2V
Display:-128*64 LCD display module,
COGDisplay Type:-FSTN,
6 O’CLOCK,
Transflective / Positive

Additional Information:

• Item Code: OMP-M063

Product Details:

Built-in TTL PL-2303HX Serial Controller IC. Standard USB type A male and TTL 3pin connector. Simple serial communication. Super terminal use; commonly used serial debugging tool. Simple and Easy way to give USB support to your designs
color: blue
Comprehensive material
XP system installation process: Downloaded the driver Click the icon to start the installation, click Next until completed. Installed correctly; can see in Device Manager - Ports - USB-To-Serial Comm Port (COM3 / COM port you connected the USB interface will display different)
Second, insert the to upgrade small plate, and the system will automatically load the driver for it. Note: TXD and RXD DuPont line shorted to normal test module.
Available for Linux, Mac, WinCE and Windows (XP, 2003), Vista, Win 7/8
XP system installation process:
Downloaded the driver Click the icon to start the installation, click Next until completed.
Installed correctly; can see in Device Manager - Ports - USB-To-Serial Comm Port (COM3 / COM port you connected the USB interface will display different)
Second, insert the to upgrade small plate, and the system will automatically load the driver for it. Note: TXD and RXD DuPont line shorted to normal test module
Connection:
RX TO TX;
TX TO RX;
GND to GND
Function line Description: Red-VCC, black-GND, Green-TXD, white-RXD
Module use
1, install the driver,
2, restart the computer,
3, the module is plugged into the computer's USB interface, the system will automatically install the driver
4 TXD and RXD connected (ie with a DuPont line a plug in the TXD an interpolation RXD), the module can spontaneously self-closing,
5, open [serial debugger
Package Contents: 1 X LCD Module Display
Only the above package content, other products are not included.
Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1-3cm.

Additional Information:

• Item Code: OMP-M020

Product Details:

Features:
Driver IC: SH1106.
Resolution: 128x64.
Font color: blue light, white light.
Support voltage: 3.3V/5.0V.
Working temperature: -40~85 degrees.

Specifications:
Driver chip: SH1106
Support interface: SPI
Resolution: 128×64
Display size: 1.3 inches
Display color: white, blue (optional)
Dimensions: approx. 35.5x33.7x1.2mm/1.40x1.33x0.05in
Glass size: approx. 34.5x23x1.45(mm)
Display area: approx. 29.42x14.7(mm)
Positive and negative tolerance: 0.2mm
Number of needles: 7Pin
Viewing angle: above 160°
Working temperature: -40 80
Storage temperature: -45 85
Working voltage: 3.3V / 5V

Additional Information:

• Delivery Time: 1 to 2 days

Product Details:

• A single module can drive an 8 * 8 common cathode lattice
• Only one external register is used to set the segment current of each LED
• Module with input and output interfaces, supports multiple modules cascade
• MAX7219 is an integrated serial input / output common cathode display driver
• A convenient four line serial interface can connect all the general-purpose microprocessors

Additional Information:

• Item Code: OMP-M099
• Delivery Time: 1 to 2 Days