JTAG Emulator & Debugger

Product Details:

DESCRIPTION:-

Support Full range of HCS08, HCS12 (X) full range, Cold fire V1 full range, Can be downloaded online , single-step debugging , simulation, observe all registers and global variables values.2 Support the development environment,CodeWarrior V10.1 V10.2,CodeWarrior V5.0 V5.1 (16Bit microcontroller development environment),CodeWarrior V6.2 V6.3(8Bit microcontroller development environment),3. Environment: WINXP / WIN7 32/64 bit, 4.BDM clock up40M, 5. Support Firmware Online Upgrade, 6.BDM interface is the official standard version, is defined as follows:

1. BKGD 3.NC 5.NC
2. GND 4.RST 6.VDD

Supported chips:

HCS08 8Full range of

MC9S08AC128, MC9S08AC16, MC9S08AC32, MC9S08AC48, MC9S08AC60, MC9S08AC8, MC9S08AC96, MC9S08AW16, MC9S08AW16A, MC9S08AW32, MC9S08AW48, MC9S08AW60, MC9S08AW8A,MC9S08DE32, MC9S08DE60, MC9S08DN16, MC9S08DN32, MC9S08DN48, MC9S08DN60, MC9S08DV128, MC9S08DV16, MC9S08DV32, MC9S08DV48, MC9S08DV60, MC9S08DV96, MC9S08DZ128, MC9S08DZ16, MC9S08DZ32, MC9S08DZ48, MC9S08DZ60, MC9S08DZ96,MC9S08EN16, MC9S08EN32,MC9S08EL16, MC9S08EL32,MC9S08GB32, MC9S08GB32A, MC9S08GB60, MC9S08GB60A, MC9S08GT16, MC9S08GT16A, MC9S08GT32, MC9S08GT32A, MC9S08GT60, MC9S08GT60A, MC9S08GT8A,MC9S08JM16, MC9S08JM32, MC9S08JM60, MC9S08JM8,MC9S08JR12,MC9S08LC36, MC9S08LC60,MC9S08QA4, MC9S08QD2, MC9S08QD4, MC9S08QE128, MC9S08QE16, MC9S08QE32, MC9S08QE32, MC9S08QE4, MC9S08QE64, MC9S08QE8, MC9S08QE96, MC9S08QG4, MC9S08QG8,MC9S08RC16, MC9S08RC32, MC9S08RC60, MC9S08RC8, MC9S08RD16, MC9S08RD32, MC9S08RD60, MC9S08RD8, MC9S08RE16, MC9S08RE32, MC9S08RE60, MC9S08RE8, MC9S08RG32, MC9S08RG60,MC9S08SG16, MC9S08SG32, MC9S08SG4, MC9S08SG8,MC9S08SH16, MC9S08SH32, MC9S08SH4, MC9S08SH8,MC9S08SLL16, MC9S08SLL8,

HCS12 (X) 16Full range of

MC9S12A128B, MC9S12A256B, MC9S12A32, MC9S12A64, MC9S12A512,MC9S12B64, MC9S12B128,MC9S12C32, MC9S12C64, MC9S12C96,MC9S12D32, MC9S12D64, MC9S12DB128A, MC9S12DB128B, MC9S12DG128B, MC9S12DG256B, MC9S12DJ128B, MC9S12DJ256B, MC9S12DJ64, MC9S12DP256B, MC9S12DJ64, MC9S12DP256B, MC9S12DP512, MC9S12DT128B, MC9S12DT256, MC9S12DT256B,MC9S12E32, MC9S12E64, MC9S12E128, MC9S12E256,MC9S12G96, MC9S12G128,MC9S12GC16, MC9S12GC32, MC9S12GC128,MC9S12H128, MC9S12H256, MC9S12HN64, MC9S12HZ64, MC9S12HZ128, MC9S12HZ256,MC9S12HA32, MC9S12HA48, MC9S12HZ64,MC9S12HY32, MC9S12HY48, MC9S12HY64,MC9S12I32, MC9S12I128,MC9S12KC64, MC9S12KC128, MC9S12KG64, MC9S12KG128, MC9S12KG256, MC9S12KL64, MC9S12KL128, MC9S12KT128, MC9S12KT256,MC9S12NE64,MC9S12P32, MC9S12P64, MC9S12P96, MC9S12P128,MC9S12Q32, MC9S12Q64, MC9S12Q96, MC9S12Q128,MC9S12T64,MC9S12UF32,MC9S12XA128, MC9S12XA256, MC9S12XA512,MC9S12XB128, MC9S12XB256,MC9S12XD64, MC9S12XD128, MC9S12XD256, MC9S12XDG128, MC9S12XDP512, MC9S12XDQ256, MC9S12XDT256, MC9S12XDT384, MC9S12XDT512,MC9S12XEG128, MC9S12XEP100, MC9S12XEP768, MC9S12XEQ384, MC9S12XEQ512, MC9S12XET256,MC9S12XFR128,MC9S12XHY128, MC9S12XHY256,MC9S12XS64, MC9S12XS128, MC9S12XS256.

Product Details:

The MSP-FET430UIF is a powerful Flash emulation tool to quickly begin application development on the MSP430 MCU. It includes USB debugging interface used to program and debug the MSP430 in-system through the JTAG interface or the pin saving Spy Bi-Wire (2-wire JTAG) protocol. The Flash memory can be erased and programmed in seconds with only a few keystrokes and since the MSP430 Flash is ultra-low power, no external power supply is required. The debugging tool interfaces the MSP430 to the included integrated software environment and includes code to start design immediately. The MSP-FET430UIF development tools supports development with all MSP430 Flash devices.

• SB debugging interface (MSP-FET430UIF) connects a Flash based MSP430 MCU to a PC
• Software configurable supply voltage between 1.8 and 3.6volts at 100mA
• Supports JTAG Security Fuse blow to protect code
• Supports all MSP430 boards with JTAG header
• Supports both JTAG and Spy-Bi-Wire (2-wire JTAG) debug protocols

Product Details:

PRODUCT DETAILS

The ST-LINK/V2 is an in-circuit debugger and programmer for the STM8 and STM32 microcontroller families.

The single wire interface module (SWIM) and JTAG / serial wire debugging (SWD) interfaces are used to communicate with any STM8 or STM32 microcontroller located on an application board.

STM8 applications use the USB full speed interface to communicate with STMicroelectronic’s ST Visual Develop (STVD) or ST Visual Program (STVP) software.

FEATURES

5 V power supplied by USB connector

Operating temperature 0 to 50 °C

USB standard A to Mini-B cable provided

USB 2.0 full speed interface compatible

1.65 V to 5.5 V application voltage supported on SWIM interface

SWIM programming speed rate: 9.7 Kbytes/s in low speed and 12.8 Kbytes/s in high speed

SWIM cable for connection to the application via a pin header or a 2.54 mm pitch connector

JTAG cable for connection to a standard JTAG 20-pin pitch 2.54 mm connector

Direct firmware update feature supported (DFU)

Additional Information:

• Item Code: OMP-P066
• Delivery Time: 1 to 2 Days

Product Details:

Features:
- USB2.0 high speed port(480Mbit/s)
- 14PIN standard JTAG port, support TI core processor
- Support multi processorss: TMS320C28x, TMS320C54x, TMS320C55x, TMS320C64x+, TMS320C674x, ARM 9,  ARM Cortex R4, ARM Cortex A8
- Support power off detection
- Support FTDI device drive
- Support time self adaption
- Support Code Composer Studio v4 or above
- Support LED light display control USB connection
Operation System:
- Windows 2000
- Windows XP
- Windows Vista
- Windows 7
Package Included:
- 1* XDS100 V2 Emulator
- 1* USB 2.0 Cable
- 1* 14Pin flat cable

Additional Information:

• Delivery Time: 15 to 17 Days

Product Details:

Product Description:
XDS100v3 Emulator is the third version of XDS100 JTAG emulation technology, supporting a variety of TI's chip debugging. Support USB2.0 high-speed interface, theoretical speed of 480M / s, through the 14P/20P interface for emulation debugging, support Code Composer Studio (CCSV5/V6/V7/V8/V9/V10 and higher versions. Can be used for WinXP/Win7/Win8/Win10 and other operating systems.
Features:
 
- USB2Q high speed interface, up to 480Mbit/s
- USB side self-recovery insurance protection, to protect your computer
- JTAG side static chip protection, anti-static ±15KV, stable and reliable
- Support power failure detection
- Support adaptive clock
- Support JTAG reset, wait and reset start mode
- Support power-on reset startup mode
- Support a variety of FTDU device driver
- Support adjustable TCLK clock
- Support 1.8V~5V JTAG voltage standard
- Support TI standard 14PIN JTAG interface
- Support TI standard 20PIN JTAG interface
- Support 2-wire cJTAG interface, simplify the connection with the target board
- Driver-free, automatic recognition when plugged into the emulator
- Support high-speed USB code download
- Support FLASH online emulation of DSP
- Faster emulation and download speed
- Support CCS V5.2 or above, new version CCSV10 are supported
- Support IAR for ARM V6.4 or above
- Support Flash Programmer 2 burn-in software
- Support uniflash standalone burning software.
- Support SmartRF Studio configuration software.
- Support TMS320c28xx, TMS320C54xx, TMS320C55xx, TMS320C674x, TMS320C64X+.
TMS320C64X+, TMS320C66x, ARM9, ARM Cortex 
M0/M3/M4/A8/A9/A15/R4/R5. TMS470LSxx. TMS570LSxx, Davinci.
Zigbee (32bit) CC26xx series (such as
CC2652/CC2650/CC2642/CC2640/CC2630/CC2620, etc.
CC1310/CC1350, etc.), CC2538, etc.
. Support WinXP/Win7/Win8/Win 10/Linux etc.

Product Details:

PRODUCT DETAILS 
J-Link is a USB powered JTAG emulator supporting a large number of CPU cores. Based on a 32-bit RISC CPU, it can communicate at high speed with the supported target CPUs.J-Link is used around the world in tens of thousands places for development and production (flash programming) purposes. J-Link is supported by all major IDEs such as IAR EWARM, Keil MDK, Rowley Cross Works, Atollic True STUDIO, IAR EWRX, Renesas HEW, Renesas e2studio, and many others. Including all models, more than 100,000 J-Links have been sold so far, making J-Link probably the most popular emulator for ARM cores and the de-facto standard.

FEATURES

Direct download into flash memory of most popular microcontrollers supported,Supported CPUs Any ARM7/9/11, Cortex-A5/A8/A9, Cortex-M0/M1/M3/M4, Cortex-R4,RX100/RX200/RX610/RX621/RX62N/RX62T/RX630/RX631/RX63N,Download speed up to 1 MByte/second,Supports unlimited breakpoints in flash memory,Setting breakpoints in external flash memory of Cortex-M systems is possible,J-Link's Unlimited Flash Breakpoints technology only,Supported by all major IDEs,Supports concurrent access to CPU by multiple applications,Cross platform support (runs on Windows, Linux, Mac OS X) 4,Intelligence in the emulator firmware,Remote Server included. Allows using J-Link remotely via TCP/IP,GDB Server included,Production flash programming software (J-Flash) available,Software Developer Kit (SDK) available,Supports multiple target interfaces JTAG, SWD,Supports SWV/SWO (Serial Wire Viewer/Serial wire output),Wide target voltage range 1.2V-3.3V,5V tolerant,Supports JTAG chains with multiple devices,Embedded Trace Buffer (ETB) support,Various target adapters available, including optical isolation adapter,RDI interface DLL available,Fully plug and play compatible,No power supply required, powered through USB,Support for adaptive clocking,All JTAG signals can be monitored, target voltage can be measured,Target power supply J-Link can supply up to 300 mA to target with overload protection

Package List

1 x J-link V9 ARM Emulator
1 x USB Cable
1 x Connector Cable
1 x J-link ULINK2 Emulator V8 all-ARM JTAG Adapter Converter
1 x CD
It also supports MINI2440, TQ2440 and other New Version and Popular ARM board. It includes SWD 6PIN interface and SWD 4PIN port. It is also compatible with sockets as follow 20PIN Pitch = 2.54MM20PIN Pitch = 2.0MM10PIN Pitch = 2.54MM10PIN Pitch = 2.0MM14PIN Pitch = 2.54 MM

Additional Information:

• Item Code: OMP-031
• Delivery Time: 1 to 2 days

Product Details:

Ulink 2 USB JTAG Emulator ARM9 Cortex Keil Ulink II GH2,ARM USB Compatible JTAG Adapter Debugger Keil Ulink-II,Ulink 2 does not need any specific drivers. It is automatically configured as a HID by Plug and Play in Windows. Latest Upgraded version of the ULink emulator. Not only has the ULINK2 emulator all the features of ULINK, but also serial wire debug (SWD) support, Clock return support and features such as real-time agent. Conveniently carried out target hardware on-chip debugging (using on-chip JTAG, SWD, and OCDS), Flash Programming. Standard Windows USB driver support Plug and Play ULINK2, Support for ARM Cortex-M3-based serial wire debug, Support the program to run during the read-write memory, terminal emulation and serial debug output, Support 10-pin cable (also supports 20-pin cable)

Breakpoints RAM : Unlimited
ROM Breakpoints (ARM7 / 9) : 2 max
ROM Breakpoints (Cortex-M3) : 6 max
Execution breakpoints (Set While Executing) : yes
Access Breakpoints (ARM7 / 9) : 2 max (R / W Only, With Value)
Access Breakpoints (Cortex-M3) : 4 max (With Value)
Trace History : no
Real-Time Agent : yes
JTAG clock : <= 10MHz
JTAG RTCK support (Return Clock) : yes
Memory R / W (Bytes / sec) : 28K
Flash R / W (Bytes / sec) : 25K
Single-Step (Fast) (Instructions / sec) : 50
Supported Devices:
Actel (ARM7/ARM9/Cortex Family)
COREMP7, Cortex-M1

DETAILS:

Color: White
Item size: 112*56*23mm
Cable length: about 1.5m
Net weight: 154g
Packing:
1x Ulink2 emulator
1x 20pin flat cable
1x USB 2.0 Cable

Additional Information:

• Item Code: OMP-P016
• Delivery Time: 1 to 2 days