Relay Modules

Product Details:

This is a 2 Channel 5V Relay interface board, be able to control various appliances, and other equipments with large current It can be controlled directly by Microcontroller (8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic).5V 2-Channel Relay interface board, and each one needs 15-20mA Driver Current Equipped with high-current relay, AC250V 10A; DC30V 10A Standard interface that can be controlled directly by microcontroller (8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic) Indication LED's for Relay output status.

DETAILS

Module with pine le relay control, ac voltage maximum 250 V, ac current maximum 10 A, dc voltage maximum 30 V, dc current maximum 10 A; The 8550 transistor drive, drive ability; Working voltage 5 V. Has the fixed bolt hole and easy installation Power indicator (green), Two ways of relay status indicator light (red) Module interface specifications (6 wire)

1. VCC external 5V

2. GND external GND

3.1N1-1N2 interchange relay control interface by single chip IO

Using a large current relay, AC250V 10A DC30V 10A, Contact some independent wiring, safe and reliable Standard interface that can be extended in a variety of development board With fixed screw holes for easy installation, Suitable for a variety of platforms 51/AVR/AVR/ARM, Size (L x W x H) 54mm x 47mm x 18mm.

PACKAGE CONTENTS

1 x 2-Channel 5V Relay Module

Additional Information:

• Item Code: OMP-M004

Product Details:

This is a 5V 4-Channel Relay interface board, be able to control various appliances, and other equipments with large current. It can be controlled directly by Microcontroller (for Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic).

1.5V 4-Channel Relay interface board, and each one needs 15-20mA Driver Current

2. Equipped with high-current relay, AC250V 10A; DC30V 10A

3. Standard interface that can be controlled directly by microcontroller (for Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic)

4. Indication LED's for Relay output status

5. SIZE 54MM * 75MM

Additional Information:

• Item Code: OMP-M005
• Port of Dispatch: Mumbai

Product Details:

Dual Trigger design, using special two-way driver IC design, fly away to ride the world premiere of electronic Science and Technology, Anti-interference ability, using the freewheeling diode protection Part of the relay contacts using double-sided bold wiring for a large current through the safe and reliable, 5.08mm high-quality input and output terminals are used, the wiring is more convenient and suitable for PLC control, The inputs can be set high and low trigger control more flexible, Each relay has a pull indicator, working status of the relay at a glance, Each relay output leads to a normally open and normally closed two electric shock, use convenient and flexible, With fixed screw holes for easy installation, Finished by 100% functional testing and stability testing.

PACKAGE INCLUDES

1pc * 8-channel relay module

1pc *the remote control

Additional Information:

• Item Code: OMP-M058

Product Details:

Operating voltage 5V.This relay module is 5V active low. It is an 8-channel relay interface board, which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, PLC, etc. It is also able to control various appliances and other equipments with large current. Relay output maximum contact is AC 250V 10A and DC 30V 10A. Standard interface can be directly connected with microcontrollers. Red working status indicator lights are conducive to the safe use. Widely used for all MCU control, industrial sector, PLC control, smart home control.

Additional Information:

• Item Code: OMP-M051

Product Details:

Relay modules suitable for switching of higher voltages and perfect for use with microcontrollers including Arduino, ARM, AVR and PIC, The relays used are rated up to 10A and have NO/NC contacts. Each channel has an LED indicator to show the relay is on, Connects directly to a microcontroller, LED Indicator for each channel, Switching Capacity: 10A, Maximum Voltage: AC250V / DC30V

DETAILS:

Trigger Mode: Low Level Trigger

Material: Metal+ Plastic

Color: As pictures show

Voltage Supply: 5V

PACKAGE INCLUDES:

1 Piece Relay Board Module

Additional Information:

• Item Code: OMP-M054

Product Details:

PRODUCT DETAILS

5V One 1 Channel Relay Module With optocoupler For Arduino PIC AVR DSP ARM.
Surrounded by fixed mounting holes, external connection use rotating crimping terminal, make connection firmer Optical coupling isolation, input and output power optional independent control.

OTHER DETAILS

Materials: Metal, Plastic, Electric Parts
Pole Number: 1 Channel
Load: 10A
Size: Approx. 51x31x19mm/ 2.01x1.22x0.75inch

Additional Information:

• Item Code: OMP-M108
• Delivery Time: 1 to 2 Days

Product Details:

Trigger mode:
High level5V relay module Can be used for microcontroller development board module or home appliance control5V - 12V TTL control signal Can control DC or AC signal, also 220V AC load Normally open / closed contact Controlled lights bright when pull and not shine when disconnect Increase the transistor drive relay coils, control pins high impedance Control pins have pull down circuit to prevent malfunction of relay vacant

Additional Information:

• Item Code: OMP-M02

Product Details:

This is a delay timer module with high performance, which is convenient and practical for users.

FEATURES:

New upgrades to simplify, meeting the users\'' needs.

Increase the power supply anti-reverse function.

LED 3 digits display, intelligent control, time relay/delay function.

The use of Opto isolated input and output, enhanced anti-jamming capability and consumption.

The last setting parameters can be memorized after power off.

Power saving function, one-key switch, can turn off the display.

To ensure stability, industrial grade PCB board.

WORKING MODES SELECTION:

After power on, long press K1 for 2s, later into the selection of modes: P1~3.
P-1: Monostable trigger delay, a signal to trigger relay, time is up, the relay disconnect;
P-2: A signal trigger and countdown begins, T1 seconds after, the relay open T2 seconds, then close;
P-3: Open T1 seconds, disconnect T2 seconds, infinite loop. Users can set the relay time T1 and T2;

DETAILS:
Display: LED Digital Display
Voltage: DC 12V / DC 24V (Optional)
Timing Range(Settable): 0~999.9 seconds; 0~9999 seconds; 0~9999 minutes
Relay Specification: DC 5~30V 10A or AC 220V 10A
Static Current: 20mA
Working Current: 50mA
Working Temperature: -40-85C
PCB Size: 65 * 38 * 18mm / 2.56 * 1.5 * 0.7in (L * W * H)
PCB Weight: 26g / 0.93oz
Package Size: 11.5 * 7.5 * 2cm / 4.53 * 2.95 * 0.8in (L * W * H)

PACKAGE LIST:
1 * Delay Timer Module

Additional Information:

• Item Code: OMP-M001
• Pay Mode Terms: L/C (Letter of Credit),T/T (Bank Transfer),D/P,D/A,Other
• Port of Dispatch: Mumbai

Product Details:

FEATURES:

This relay module is 5V active low, comes with a remote controllers.

The 1 channel 5V Relay Module is level triggered, and suitable for IO port output.

It is a 1-channel relay interface board, which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, PLC, etc.

It is also able to control various appliances and other equipments with large current.

The output contact rating: 250VAC-10A 125VAC-10A???30VDC-10A 28VDC-10A, which can drive the most of household appliances or industrial control.

Standard interface can be directly connected with microcontrollers.

With the LED indicator light (For Connection, disconnection).

The Relay has normally closed contact and normally open contact.

With the relay coil absorber diode protection.

Active-low signal input, VCC, GND power supply input terminal.

Adopts the opto-isolator, safe and reliable, high anti-interference.

With compact portable design for easy carry.

APPLICATIONS:

Support all MCU control, industrial circle, PLC control, household appliances control, smart home control, etc.

DETAILS:
Working voltage: 5V
Control distance: 8m
The Relay Board has the 3mm screw holes for easy installation.

Relay Module interfaces: VIN + Positive pole 5V, GND Negative electrode; the middle port of the three ports is Community port, the other two ports are normally open port and normal close port (the front end circuit of the relay output and input is insulative).

Color: Blue (Relay Module), Black (Remote Controller)
Main item size: 5.0 * 2.0 * 1.8cm / 1.97 * 0.79 / 0.28in (Relay Module), 8.5 * 4.0 * 0.7cm / 3.35 * 1.57 *0.28in (Remote Controller)

Main item weight: 15g / 0.53oz (Relay Module); 14g / 0.5oz (Remote Controller)

Package size: 11.5 * 7.5 * 3.0cm / 4.53 * 2.95 * 1.18in

Package weight: 33g / 1.17oz

PACKAGE LIST:
1 * 5V 1 channel Relay Module
1 * Remote Controller

Additional Information:

• Item Code: OMP-M029
• Pay Mode Terms: L/C (Letter of Credit),T/T (Bank Transfer),D/P,D/A,Other
• Port of Dispatch: Mumbai

Product Details:

FEATURES:

This module can control five independent relays and one total relay output normally open or normally closed electric shock. The working time of each relay can be set separately. In the set time range, the relay action output normally open or normally closed electric shock, in order to achieve the control of the equipment.

 

OTHER DETAILS:-

Voltage: AC/DC 12V
Colour:blue
Size:120*93*19mm
Material:metal

Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1-3cm.

PACKAGE LIST: 

1 * Delay Timer Module

 

Additional Information:

• Item Code: OMP-M002
• Port of Dispatch: Mumbai