Wireless Transceiver Modules

Product Details:

XL1278-D01 wireless module is latest Lora TM modulation technology wireless chip, the module in addition to the traditional GFSK modulation technology, but also uses the LoRa (remote) spread spectrum technology, with ultra-long distance spread spectrum communication, high anti-interference and minimizes current consumption. Using Lora TM mode can achieve high -148dbm high sensitivity, and with integrated +20 dBm power output, you can achieve low-power ultra-long distance transmission, the module is suitable for any complex environment of wireless data transmission applications, such as: Table, intelligent home control, automotive electronics, security alarm, industrial monitoring and control systems, long-range agricultural irrigation control systems and other applications. The module can be easily embedded into the customer's existing product or system design, the standard SPI interface, making communication easy and concise. Customers only in the original micro-control device to compile a simple communication protocol, you can achieve two-way communication to achieve data transmission.

 

CHARACTERISTICS

FSK / GFKS technology, LoRa (remote) spread spectrum technology

Half duplex communication

Super anti-jamming (channel rejection ratio: 56db)

High Receive Sensitivity -139dbm. (32M Passive 10ppm Crystal)

ISM multi-band, no need to apply for frequency free use.

Multi-frequency optional, a variety of transmission rate. Can be used in FDMA and FM technology.

Intelligent reset, low voltage monitoring, timer wakeup, low power mode, sleep mode

Low power consumption to accept current: 10-12mA

256-bit FIFO TX / RX

RSSI channel detection function

Transmission mode: FIFO / direct mode (recommended FIFO pack mode)

Configuration: AFC / air wake-up function / low power consumption / carrier sense / FEC error correction / AEC encryption

Ultra-long distance transmissions open up to 5KM.

Module size: 17 * 16.5mm

Additional Information:

• Item Code: OMP-M066
• Delivery Time: 1 to 2 days

Product Details:

Supply voltage: 3.2V~5.5V.

Default address range (open field test): About 600m (maximum communication distance adjustable reach 1000m, the baud rate is 5000bps)

Default idle current: 16MA (In different working modes operating current is different)

Module dimensions: 27.8 x 14.4 x 4mm

Operating frequency range: 433.4-473.0MHz, up to 100 channels of communication

The maximum transmit power: 100mW (settable)

Module support software upgrade

Default factory settings: Mode FU3, baud rate is 9600bps, communication channels CH001 (433.4M)

Additional Information:

• Item Code: OMP-M065
• Delivery Time: 1 to 2 days

Product Details:

Maximum operating speeds up to 2Mbps

GFSK modulation efficiency & Anti-interference ability

Great for industrial control applications as well

125 Channels with Multi-point communication and frequencies to meet the most communication

Built-in hardware CRC error detection

Multipoint communication address control

Low-power operation 1.9 ~ 3.6V

Consumes only 1uA on Power down mode

Built-in 2.4 GHz antenna

Can be directly connected to a variety of microcontrollers

Easy software programming

Consumes only 1uA on Power down mode

Built-in voltage regulator

Standard DIP Pitch Interface for embedded applications

Size: 34mm X 17mm X 1mm

Additional Information:

• Item Code: OMP-M050
• Delivery Time: 1 to 2 days

Product Details:

EM18 is a RFID reader which is used to read RFID tags of frequency 125 kHz.After reading tags, it transmits unique ID serially to the PC or microcontroller using UART communication or Wiegand format on respective pins.EM18 RFID reader reads the data from RFID tags which contains stored ID which is of 12 bytes.

FEATURES AND OTHER DETAILS

Operating voltage of EM-18 +4.5V to +5.5V

Current consumption 50mA

Can operate on LOW power

Operating temperature 0C to +80C

Operating frequency 125 KHz

Communication parameter 9600bps

Reading distance 10cm, depending on TAG

Integrated Antenna

Additional Information:

• Item Code: OMP-M059

Product Details:

The module uses SPI to communicate with microcontrollers. The open-hardware community already has a lot of projects exploiting the RC522 - RFID Communication, using Arduino.

FEATURES-

Integrated MF RC522,13.56MHz contactless communication card chip, Low-voltage, low-cost, small sizes of the non-contact card chip to read and write., Suitable for Smart meters and portable handheld devices, Advanced modulation and demodulation concept completely integrated in all types of 13.56MHz passive contactless communication methods and protocols,14443A compatible transponder signals,ISO14443A frames and error detection, Supports rapid CRYPTO1 encryption algorithm, terminology validation MIFARE products,MFRC522 support MIFARE series of high-speed non-contact communication, two-way data transmission rate up to 424kbit/s,Low cost, and ideal for user equipment development, The reader and RF card terminal design meets advanced applications development and production needs, Can be directly loaded into the various reader molds, very convenient.

OTHER DETAILS-

Operating Current 13-26mA / DC 3.3V,Idle Current 10-13mA / DC 3.3V,Sleep Current < 80uA,Peak Current < 30mA,Operating Frequency 13.56MHz,Supported card types mifare1 S50, mifare1 S70 MIFARE Ultra light, mifare Pro, MIFARE DESFire,Environmental Operating Temperature -20 - 80 degrees Celsius, Environmental Storage Temperature -40 - 85 degrees Celsius, Relative humidity relative humidity 5% - 95%,Reader Distance 50mm / 1.95" (mifare 1),Module Size 40mm x 60mm,Module interface SPI, Data transfer rate Maximum 10Mbit/s.

PACKAGE INCLUDES-

1x a RFID-RC522 Module

1x the Standard S50 Blank Card

1x S50 special-shaped card (as shown by the key ring shape)

1x Straight Pin

1x Curved Pin

Additional Information:

• Item Code: OMP-M057
• Delivery Time: 1 to 2 days

Product Details:

Working Voltage 1.9 to 3.6 V low voltage
In the 2Mbit / s rate @ 0dBm output peak current of 11mA32u
A standby mode power consumption130us fast switching and wake-up time
With on-chip voltage regulator oltage regulators
In the 1.9 to 3.6V low voltage operation
MultiCeiverMT hardware provides simultaneous six receiver functions, 2Mbit / s high-quality VoIP makes it possible to130 us quickly switch and wake time
Has the on-chip voltage regulator voltage regulators
2 Mbit / s rate of the peak current of 12.5mA received400nA power down mode

Additional Information:

• Item Code: OMP-M062
• Delivery Time: 1 to 2 days

Product Details:

This is the XBee 1mW Wire Antenna Series 1 XB24-AWI-001 module. It is Easy to use. These modules can communicate point to point, from one point to a PC, or in a mesh network. Just power on and start communicating and the XBee 802.15.4 modules are the easiest-to-use, most reliable and cost-effective RF devices we've experienced. The 802.15.4 XBee modules provide two friendly modes of communication a simple serial method of transmitting/receive or a framed mode providing advanced features. XBee is ready to use out of the package, or they can be configured through the X-CTU utility or from your microcontroller.

Additional Information:

• Item Code: OMP-X003

Product Details:

XBEE 2mW Wire Antenna S2C provides cost-effective wireless connectivity to devices. Module communicates in point-to-point, peer-to-peer, and multipoint/star configurations. This module communicates with ZigBee mesh network. XBee 802.15.4 modules seamlessly interface with compatible gateways, device adapters, range extenders, and providing developers with beyond-the-horizon connectivity.

FEATURES

Low-power module uses only ~33 mA to transmit

Integrated Wire Antenna

15 general-purpose I/O lines

Indoor range of 200 feet, or outdoors up to 4000 feet line-of-sight

Firmware upgrades via UART, SPI, or over the air

Low-power module uses only ~33 mA to transmit

Additional Information:

• Item Code: OMP-X002

Product Details:

This RF module comprises of an RF Transmitter and an RF Receiver.

The transmitter/receiver (Tx/Rx) pair operates at a frequency of 434 MHz

An RF transmitter receives serial data and transmits it wireless through RF through its antenna connected at pin4.

The transmission occurs at the rate of 1Kbps – 10Kbps.

The transmitted data is received by an RF receiver operating at the same frequency as that of the transmitter.

Additional Information:

• Item Code: OMP-M069

Product Details:

RFM95W 915Mhz - LoRa Ultra Long Range Wireless Transceiver (functionally comparable to SX1276) The RFM95W transceivers feature the LoRa long range modem that provides ultra-long range spread spectrum communication and high interference immunity while minimizing current consumption.

Using Hope RF’s patented LoRa modulation technique RFM95W can achieve a sensitivity of over -148dBm using a low cost crystal and bill of materials. The high sensitivity combined with the integrated +20 dBm power amplifier yields industry leading link budget making it optimal for any application requiring range or robustness.

LoRa also provides significant advantages in both blocking and selectivity over conventional modulation techniques, solving the traditional design compromise between range, interference immunity and energy consumption.

These devices also support high performance (G) FSK modes for systems including WMBus, IEEE802.15.4g. The RFM95W deliver exceptional phase noise, selectivity, receiver linearity and IIP3 for significantly lower current consumption than competing devices.

FEATURES:

LoRa Modem

168 dB maximum link budget

+20 dBm - 100 mW constant RF output vs. V supply.

+14 dBm high efficiency PA.

Programmable bit rate up to 300 kbps

High sensitivity: down to -148 dBm.

Bullet-proof front end: IIP3 = -12.5 dBm.

Excellent blocking immunity

Low RX current of 10.3 mA, 200 nA register retention

Fully integrated synthesizer with a resolution of 61 Hz

FSK, GFSK, MSK, GMSK, LoRa and OOK modulation

Built-in bit synchronizer for clock recovery.

Preamble detection

127 dB Dynamic Range RSSI

Automatic RF Sense and CAD with ultra-fast AFC

Packet engine up to 256 bytes with CRC

Built-in temperature sensor and low battery indicator.

Module Size???16*16mm

Additional Information:

• Item Code: OMP-M078
• Delivery Time: 1 to 2 days

Product Details:

PRODUCT DETAILS

LoRa Modules are long range low power RF Modules. Great for IoT applications to send sensor data to the cloud over long ranges. This LoRa 433MHz module designed by AI-THINKER, which based on the chip SX1278. The SX1278 RF module is mainly used for long-range spread spectrum communication. It can resist Minimize current consumption.

OTHER DETAILS

Operating Voltage: 1.8 - 3.7V, default 3.3V

Working Current, receive: less than 10.8mA(LnaBoost closed, Band 1)

Frequency range: 420 - 450MHz

Working temperature: -40- +85 degrees

LoRaTM spread spectrum communication

+20dBm - 10mW. Stable RF output power when input voltage changed

Half-duplex SPI communication

Programmable bit rate can reach to 300kbps

Support FSK, GFSK and OOK Modulation Mode

Automatically detect RF signal, CAD mode and super high speed AFC

Wireless Standard: 433MHz

Port: SPI/GPIO

Transmit: less than 120mA(+20dBm)

Sleep model: 0.2uA

Additional Information:

• Item Code: OMP-W036
• Delivery Time: 1 to 2 Days

Product Details:

PRODUCT DETAILS

CC2500 RF Modem is a transceiver module which provides easy to use RF communication at 2.4 Ghz.

DETAILS

Operating temperature range: -40 85

Operating voltage:1.8~ 3.6 Volts.

Available frequency at : 2.4-2.483 GHz

Programmable output power (up to 1dBm).

Hi sensitivity (-101dBm @10kbps)

Low current consumption.

Easy for application.

Efficient SPI interface.

Additional Information:

• Item Code: OMP-W032
• Delivery Time: 1 to 2 Days

Product Details:

PRODUCT DETAILS

RFM75 is a GFSK transceiver operating in the world wide ISM frequency band at 2400-2483.5MHz. Burst mode transmission and up to 2Mbps air data rate make them suitable for applications requiring ultra low power consumption.

RFM75 operates in TDD mode, either as a transmitter or as a receiver.

The embedded packet processing engines enable their full operation with a very simple MCU as a radio system. Auto re-transmission and auto acknowledge give reliable link without any MCU interference.

OTEHR DETAILS

Working frequency: 2400MHz–2483.5MHz

Power supply: DC 1.9V–3.6V

Modulation: FSK/GFSK

Tx Output Power: 5dBm(1mW)

Rx sensitivity: -88dBm

Data rate: 1Mbps or 2Mbps (software selectable)

Tx current: <30mA, Rx current: <23mA

Channel selection: 83 channels

Data interface: SPI

Operating temperature: -40–+85°C

Range: 70m (open air)

 

Additional Information:

• Item Code: OMP-W033
• Delivery Time: 1 to 2 Days

Product Details:

PRODUCT DETAILS

NRF24L01 is popular wireless data transceiver module, however their 4 x 2 rows of pins can be a challenge to use with a solderless breadboard.

Furthermore a power regulator is included, so you can safely power your module with anything between 4.8 and 12V.

OTHER DETAILS

Input Voltage: 5V DC

Output Voltage: 1.9~3.6V DC

Current: 12.3 mA

Transmission rate: 2Mbps

Range: <100m

FEATURES

Low power consumption

Automatic retransmission function

Supports all channel data reception

125 multi-frequency points

Built-in 2.4 GHz antenna

Dip2.54 MM spacing interface

Additional Information:

• Item Code: OMP-W034
• Delivery Time: 1 to 2 Days

Product Details:

PRODUCT DETAILS

Highly integrated, small size

High sensitivity, low power consumption

Less interfrence, longer working distance

Fsk technology, suitable for replacing ask modules

Can be used to replace ask module W/O the need of software change

No tuning required during production

APPLICATIONS

Automobile Door Opener

Garage Door Opener

Anti-theft system

Home Security

Electrical Home Appliance Control

Other wireless systems

Additional Information:

• Item Code: OMP-W035
• Delivery Time: 1 to 2 Days

Product Details:

PRODUCT DETAILS

This is a simple to use, USB to serial base unit for the XBee line. This unit works with all XBee modules including the Series 1 and Series 2.5, standard and Pro version. Plug the unit into the XBee Explorer, attach USB cable, and you will have direct access to the serial and programming pins on the XBee unit. The board is powered by the USB cable. XBee modules and USB cable are sold separately.

OTHER DETAILS

ZigBee module connector for the ease of connectivity

I/Os interface

USB interface

ONE-WIRE interface

5V/3.3V power input/output

Debugging interface

Reset Button, LEDs and user keys

Additional Information:

• Item Code: OMP-X007
• Delivery Time: 1 to 2 Days

Product Details:

PRODUCT DETAILS

This is MCP2515 CAN Module TJA1050 Receiver SPI 51 Single Chip Program Routine Arduino.

OTHER DETAILS

Power input: VCC 5V

120Ω terminal resistance

Use High-speed CAN transceiver TJA1050

SCLK SPI clock pin

INT MCP2515 interrupt pin

CS SPI SLAVE select pin (Active Pin)

SO SPI master output slave input pin

Additional Information:

• Item Code: OMP-W065
• Delivery Time: 1 to 2 Days